2.
Fender
RED
pilot light jewels, standard
faceted
jewel with nickel plated collar found on most classic Fender amps.
GENUINE
FENDER. EACH $6.99.
3. Fender pilot light jewels, faceted jewels in non-standard colors like PURPLE, BLUE, WHITE, AMBER and GREEN, so you can signal other sex maniacs from the bandstand. GENUINE FENDER. EACH $6.99.
6. Fuse assemblies
for vintage Fender and other
amplifiers, hard black phenolic plastic, MADE IN USA, genuine NEW OLD
STOCK,
great for restoring older guitar amps and D.I.Y. projects. These
assemblies
fit tweed, brown, 'white' blackface and silverface Fender amps EXACTLY.
Supplied with conical shaped fuse caps typically found on '60s-'70s
Fender
amps. EACH $15.99.
7. Fuse assemblies for vintage Fender amps, black phenolic plastic, MADE IN USA, genuine NEW OLD STOCK, great for restoring older guitar amps and D.I.Y. projects. These assemblies fit tweed, brown, 'white' and blackface and silverface Fender amps EXACTLY. Supplied with barrel shaped fuse caps (depicted below...) as found on many '50s-'70s style Fender amps. EACH $15.99.
8.
Fuse caps for early '50s Fender
amps,
ribbed
'barrel' shape, gnarly black phenolic plastic. While this style of fuse
cap was seen principally on early tweed Pro, Bassman, Champ, etc. it
was
also used as original equipment on Fender amps in the '60s and '70s.
For
example, most of the '70s Super Reverbs I've had used this kind of fuse
cap. This style is fully interchangeable with the conical type
described
below. Embossed/imprinted on top; "FUSE", directional arrow for removal
and a center dot, all in white. Most we have in stock at the moment are
NEW OLD STOCK, some are slightly used/removed from equipment. No roadie
'emergency' spare parts kit is complete without a stash of these
babies.
HARD TO FIND! EACH $8.
9. Fuse caps for older
Fender amps,
mid
'50s-'70s
conical shape, N.O.S. or good slightly used condition. EACH $8.
12. Hex nuts
for classic 1/4" input jacks and
1/4" shaft diameter potentiometers.
These high quality hex nuts fit those old Fender amps and guitars
EXACTLY;
these are the nicest current production hex nuts made today. NICKEL
PLATED
bronze alloy, nice crisp edges, perfect for restoring '50s-'70s Fender
amplifiers and guitars. including Super Reverb, tweed Twin,
Stratocaster,
Telecaster, Mustang, you name it. ONE
DOZEN FOR JUST $4.98.
13.
Reverb pan for
most vintage models including Twin Reverb, Deluxe Reverb etc., GENUINE
FENDER, classic
two spring design, fits older amps exactly, same electrical specs. Made
by Accutronics, measures 16.7 " x 4.25" . NEW. EACH $42.99.
14.
Reverb bag,
black vinyl, as found on Reissue
'65 Twin Reverb, NEW. GENUINE FENDER.
EACH
$14.99.
15.
RCA plugs
for Fender reverb units and
Vibrato
switches, old style stamped metal type for vintage '50s-'70s amps,
N.O.S.
'70s made in USA, tinned steel and brass, nice part for restoration. EACH
$2.99. TWELVE FOR JUST $19.99.
16.
Fender
"Sphinx
Glides" for amps. BIG ones
as found on recent models, measure 1.25" diameter, nickel plated steel
cup with rubber insert, set of four with screws (original Fender glides
from the '60s-80s measured 1"). While these new glides are larger, they
do 'retrofit' the old amps and are the best currently available part.
NEW.
GENUINE FENDER. SET FOR 6.99.
17.
GENUINE FENDER
piggyback 'thumbscrews", holds
head to cabinet on Showman, Bandmaster, Tremolux and other head/cabinet
sets. NEW! Heavy chrome plated steel, heavy knurling on knob. SET
OF
TWO $13.99.
18. Fender Piggyback Clip Bars for bottom of heads, chrome plated, pack of two with hardware.$24.99.
19. Fender
Piggyback Bushings for top of speaker
cabinet, internally threaded to accept piggyback thumbscrews, pack of
two
with hardware. $19.99.
20.
Fender Tube
Clips for power tubes, toothed
to dig into the plastic bases of power tubes and hold 'em in place,
bolts
down to the chassis on the same screws as on your tube sockets, dig?
These
fit vintage Fender amps exactly, pack of two.
$5.99.
21.
Fender
nine-pin tube sockets for 12AX7,
12AT7,
etc., brown phenolic plastic base, tinned solder lug contacts, mounts
from
top of chassis, standard sized mounting centers (see our CINCH nine pin
tube socket listings for dimensions...), J-slot collar for standard
sized
tube shields. GENUINE FENDER USA. EACH
$5.99.
22.
Fender
capacitor can cover as found on
reissue
Deluxe Reverb and Vibroverb, same style as depicted below, rounded
corners
on top, four mounting screw flanges on the bottom edge, inside
dimensions
5.125"X3.375"X1.25" tall. Mounting centers approx. 5.75"X3". Plating is
a bit irregular on these on the corners. EACH
$17.99.
23.
Fender capacitor can cover as
found on
reissue
'65 Twin Reverb, inside dimensions 6.5"X3.9375"X1.25" tall, rounded
corners
on top, four mounting screw flanges on the bottom edge. Mounting centers approx.
7.125"X3.5".
$16.
24. Fender capacitor can
cover as
found on
current
'59 Bassman Reissue, measures approx. 4.25"X3.875"X1.5" tall, mounting
flanges with two screw holes extend 1/2"" from the bottom of each long
side. Mounting centers approx. 5&1/16"X3".
These covers are rather basic in construction and finish but if you
want
to mount some electrolytics safely on the top deck of your D.I.Y. amp,
these are handy. EACH $15.
25. Fender tweed amp chassis
mounting screws.
Wide, slightly flattened round head machine screw. Threaded portion is
approx. 1&7/16" long. Nickel plated steel. Very nice quality. Nice
for restoring old tweed amps or reissues. Also useful for that
home-brew
tweed style project amp. GENUINE FENDER. EACH $1.99.
1. Fender Two
Button Foot switch for vintage
models
with Reverb/Vibrato, nickel plated steel, comes stock with old style
RCA
plugs, approx. 12' long black PVC flat shielded cable, great for
original
older Fender Twin Reverb, Deluxe Reverb, Showman Reverb, Bandmaster
Reverb,
Vibrolux Reverb, Pro Reverb, Princeton Reverb, Super Reverb, etc. Yes,
this switch has RCA plugs stock. GENUINE FENDER PART #099-4051-000. $42.99.
2.
Fender Two
Button Foot switch for '65 Twin
Reverb reissue, '63 Vibroverb reissue, '65 Deluxe Reverb reissue,
recent
Custom Vibrolux, recent Vibrasonic. GENUINE FENDER PART #099-4058-000.
Looks exactly like #1 depicted above but terminates in a right angle
STEREO
1/4" plug. EACH $42.99.
3. NEW!
Fender Two
Button Foot switch for models
with "CHANNEL SELECT" and "REVERB" including "Deluxe/Stage 112, Blues
Deville,
Roc Pro 700, Performer 650, Champ 25, The Twin". Modern looking unit
with
extruded aluminum body, integral dual cables with .25" ends. Genuine
Fender
part #099-4056-000. $42.99.
4. Fender
vintage
style single button foot switch
for vintage models, nickel plated steel body with black plastic snap-on
bottom, comes stock with a single RCA plug termination, approx. 12'
long
black PVC flat cable. Great for old Fender Reverb Unit, Princeton,
Vibro
Champ, Tremolux, Bandmaster, Showman and other models. GENUINE FENDER
PART
#099-4050-000. EACH
$29.99.
5.
Fender vintage
style single button foot switch
for recent models, nickel plated steel body with black plastic snap-on
bottom, comes stock with a single .25" mono plug termination, 20' LONG
neoprene jacketed shielded cable. Fender says this one's good for
Vibro-King
("early"), Prosonic Head, Tonemaster, Rumble Bass and Blues Junior.
GENUINE
FENDER PART #099-4054-000. $33.99.
7.
Fender Single Button Foot switch
for Channel
Select with square red LED indicator, cable terminates with TWO 1/4"
plugs.
Used on the Blues Deluxe, Champion 30, Champion 110, Hot Rod Deluxe,
Frontman
25R and M-80. GENUINE FENDER PART #099-4052-000. NEW. GENUINE FENDER!
$29.99.
8. Fender Three
Button Foot switch,
Channel/Gain/Reverb.
For Roc Pro, Performer 1000, Concert and Super. GENUINE FENDER PART
#099-4064-000.
Has three stomp switches with an LED on each, long extruded aluminum
floor
box, comes with foot switch to amp cord. NEW. $59.99.
9. Fender One Button Foot switch for BXR 200, M-80 Bass. GENUINE FENDER PART #099-4053-000. $29.99.
Solid
shaft GENUINE FENDER pots
are the best currently available for
repairs to older Fender amplifiers. Most of the solid shaft pots
described
below have been DISCONTINUED as accessory items by Fender, so supplies
are limited; get 'em while you still can. Case diameter is approx.
.875",
threaded portion of brass bushing measures approx. .3125" long,
standard
sized .25" diameter solid aluminum shaft measures approx. .375" long,
fits
industry standard set screw knobs found on most Fender and other
classic
amps. The mounting hardware included with these parts is not really up
to Angela Gold Bond Quality Standards so we include the right stuff.
1. 100 Ohm
Hum
Balance Pot For '65 Twin Reverb
Reissue Amp, useful as hum balance pot for other tube amps. Like the
bias
pot for this model, this one has a short 1/4" threaded brass bushing
for
mounting to the back chassis panel. Screwdriver adjusts from the front
and the rear for easy servicing. Three solder lugs. CTS quality.
GENUINE
FENDER. EACH $7.99.
2. 5K
Audio. $7.99.
3. 5K
Linear. $7.99.
4. 10K
Audio. $7.99.
5. 10K BIAS
POT.
As used on various Fender guitar amplifiers. Screwdriver adjust type.
Open
back
gives access to slotted nylon wafer body so you can adjust this pot
from
the inside of the chassis as well as from the outside. Threaded
standard
sized brass bushing for fastening to chassis. GENUINE FENDER. EACH
$7.99.
6. 50K
Reverse
Audio. EACH $7.99.
7. 100K Linear. EACH
$7.99.
8. 500K
Audio. EACH $7.99.
9. 3 Meg
Reverse Audio. EACH $7.99.
SEE OUR JAMMIN' KNOB HOE-DOWN PAGES FOR
FENDER AMP KNOBS!
Note: A pot is
variable resistor.
Most common
guitar pots have a layer of conductive carbon deposited on a
non-conductive
phenolic plastic base. A metal "wiper" sweeps along this carbon
variable
resistance path as the pot shaft is rotated, allowing us to change the
resistance and thus choose the level of attenuation. The density
pattern
of the carbon deposit determines the taper of the pot. A linear taper
pot
changes resistance evenly; at about half rotation (12 o'clock) you'll
get
roughly half the total resistance of the pot. An audio (A.K.A.
"logarithmic")
taper pot works differently; you'll have to turn it up to about three
quarters
rotation to measure one half of the resistance value of the pot. Try
this
yourself with an audio taper pot, a linear taper pot and an ohm meter.
Looking down at the top of the pot with the solder lugs facing away
from
you, put your two meter probes on the left-most and center solder lug.
Now turn the pot all the way counterclockwise and you should measure
the
total resistance of the pot (e.g. 500K or so...). Now turn the pot
shaft
clockwise to about half rotation; it helps to have a pointer type knob
on the shaft to keep track of the rotation. If you're measuring a
linear
taper pot, about half rotation should give you half of the total value
of the pot. If you turn this linear taper pot up about three quarters
rotation
you'll measure 20-25% of the total resistance value. When you turn the
pot up all the way clockwise you will probably still measure some
resistance,
say 2 to 60 or so ohms. Now try to measure an audio pot. You find that
the resistance changes only 15-20% or so at half rotation, reading half
the total resistance value only after you've reached almost three
quarters
rotation and then it drops rapidly (logarithmically...). Audio taper
pots
are commonly used when fine adjustment is needed at lower listening
levels.
There are many other pot tapers available. In my experience, different
examples of even" standard" tapers such as "audio" can vary quite a bit
in how they feel to a guitarist. Here again, experimentation with
different
pots may be worthwhile. Remember that a pot is not an amplifier; it can
only attenuate signal.
Amp
Handles And Parts For
Fender
And Other Old Guitar Amplifiers
1. Fender '60s
black strap type steel
reinforced
handle with nickel ends, complete with mounting hardware (T-nuts and
oval
head nickel plated machine screws), fit pre-CBS Super Reverb etc.
EXACTLY.
ABSOLUTELY GENUINE FENDER. EACH
$8.99.
2. Fender
Brown
Strap Handle, like above except
dark brown, complete with mounting hardware (T-nuts and oval head
nickel
plated machine screws) . GENUINE FENDER.
EACH
$8.99.
3. Fender '60s style nickel plated steel handle clasps, same part as included with the Fender strap handles depicted above. GENUINE FENDER. EACH $3.99.
4. Fender brown rubber
'dog bone' amp handle
as
found on some late '50s big tweed amps and most Fender brown and cream
Tolex covered models from the early '60s. Molded type with "Fender" old
style logo stamped into center. Nickel plated loop clasps and mounting
hardware (T-nuts and oval head nickel plated machine screws) are
included
As found on recent Fender Vibroverb reissue and other models. Looks
almost
identical to the original Fender pre-CBS parts. Excellent choice for
restoration;
fits older amps EXACTLY. GENUINE FENDER. $14.99.
6. Fender tweed amp handle clasps, little nickel plated jobs found on Champ, Deluxe, Twin, Bassman and most '50s models. Mounts on top of cabinet with two screws (NOT included...), has big spike in center to hold leather handle in place. Fits older amps EXACTLY. Identical to the original parts. GENUINE FENDER. EACH $3.99.
7.
BROWN
leather
Fender amp handle, flat type
with no center hump, DARK BROWN with contrasting white stitching, fits
older tweed amps and reissues EXACTLY. Comes packaged by Fender with
four
round head nickel plated mounting screws and matching T-nuts. NEW!
GENUINE
FENDER. EACH $17.99.
Angela
Vintage
Cotton Insulated Hookup Wire For
Fender
Guitars, Amps And Speakers
1. Cotton
covered 22 gauge wire,
made for us by the company that made it for Fender in the old days.
Perfect
for restoration of older guitar and amps, also becoming popular for
D.I.Y.
hi-fi projects. Waxed just like the old stuff. Stranded type, tinned,
very
easy to work with. NOW AVAILABLE IN A WIDER RANGE OF COLORS! Please
specify
black, white, red,
blue, green
or
yellow. $.75
PER FOOT! ONE HUNDRED FEET FOR JUST $60.
2.
Cotton covered 20 gauge wire,
preferred by some restorers for early '50s guitar (especially steel
guitar and 'Broadcaster') rewiring, amplifier
signal
circuits, etc. This stuff looks a bit thicker than the 22 guage but
thinner
than 18 guage. Waxed just like the old stuff. Stranded type, tinned,
very
easy to work with. PLEASE SPECIFY BLACK OR WHITE. IN STOCK NOW FOR
IMMEDIATE
SHIPMENT. $.99 PER FOOT, ONE HUNDRED FEET FOR JUST $80.
3.
Cotton
covered 18 gauge wire,
for wiring speakers in vintage Fender and other classic amplifiers,
also
cool for D.I.Y. amp speaker wiring. Waxed just like the old stuff.
Stranded
type, tinned, very easy to work with. PLEASE SPECIFY BLACK OR WHITE. IN
STOCK NOW FOR IMMEDIATE SHIPMENT! $.99 PER FOOT, ONE HUNDRED
FEET
FOR
JUST $80.
4. GREEN cotton
covered 18 gauge wire, for
filaments
in vintage Fender and other classic amplifiers! Waxed just like the old
stuff, stranded wire, tinned for easy soldering. Fine replacement for
that
cracked and broken solid core wire on the filaments of your old tweed
Pro
(solid core is a BUMMER for amps that get moved a lot, or that have had
the wire bent back and forth many times in servicing...). Waxed just
like
the old stuff. NEW. $.99 PER FOOT, ONE HUNDRED FEET FOR JUST $80.
As found pasted to the inside surface of your amp cabinet! We found these in an old Fender Service Center, they date from the '70s and '80s. EACH $9.99. The following tube charts in stock (tube position from left to right):
1. 6L6GC,
6L6GC,
12AT7, 12AX7A, 7025,
12AT7, 7025, 7025
2. 6L6GC, 6L6GC, 6L6GC, 6L6GC,12AT7, 7025, 7025
3. 6L6GC,
6L6GC,
12AT7, 7025, 7025, 7025
4. 6L6GC,
6L6GC,
12AT7, 7025, 12AT7, 7025, 7025
5. 6L6GC,
6L6GC,
12AT7, 7025, 7025, 7025, 12AT7, 7025, 7025
6. SOLD OUT
7. 6L6GC,
6L6GC,
12AT7, 7025, 7025
8. 6V6GTA,
6V6GTA, 7025, 7025
9. 5U4GB,
6V6GT,
6V6GT, 12AX7A, 7025
10. 6V6GTA,
6V6GTA, C6-10, 12AX7A, 7025 (A.S. Giel of the Netherlands
tells me this is for the Fender Super Champ of around 1983)
11. SOLD OUT
12. 6V6GTA,
6V6GTA, 7025, 7025, 12AT7, 7025
13. 5Y3GT,
6V6GT,
12AX7A
14. 6V6GTA,
6V6GTA, 7025, 7025, 12AT7, 7025
15. 6V6GTA, 6V6GTA, 7025, 7025, 7025, 12AT7, 7025, 7025
16. 6V6GTA,
6V6GTA, 12AX7A
17. 5Y3GT, 6V6GT, 12AX7A, 12AX7A
Note:
"7025" is functionally the same
as 12AX7/A. In the old days,
when
tubes were still made in the USA, "7025" was RCA's 'industrial' number
for 'low noise' 12AX7/A with special spiral wound filaments. Later,
many
12AX7/A were manufactured to 7025 specs rendering this distinctive
designation
somewhat obsolete. In all cases, a high quality 12AX7A, ECC83 or other
tube under the same name will replace a 7025. If you really need a 'low
noise' tube in a specific circuit position, buy a bunch of 12AX7s, try
'em out and leave the quietest one in that socket.
|